User guide
E-scooter EMC/EMI engineering: EN 17128:2020 § 11 EMC requirements, CISPR 14-1:2020 emission + CISPR 14-2:2020 immunity for household appliances and battery chargers, IEC 61000-3-2:2018 harmonic current limits (Class A/B/C/D, equipment ≤16 A per phase), IEC 61000-3-3:2013 voltage fluctuation and flicker, IEC 61000-4-2:2008 ESD ±8 kV contact / ±15 kV air (Level 4), IEC 61000-4-3:2020 radiated immunity 3-10 V/m 80 MHz-6 GHz, IEC 61000-4-4:2012 EFT/burst ±2 kV power / ±1 kV signal, IEC 61000-4-5:2014 surge 1.2/50 μs voltage + 8/20 μs current combination wave, IEC 61000-4-6:2013 conducted RF immunity 3 V_rms 150 kHz-80 MHz, FCC Part 15 Subpart B Class B 100 μV/m @ 30-88 MHz / 150 μV/m @ 88-216 MHz quasi-peak (unintentional radiator), ETSI EN 301 489-17 V3.3.1:2024 BLE/Wi-Fi 2.4 GHz + 5 GHz + 6 GHz WLAN, motor controller PWM 8-20 kHz fundamental + 100s-MHz radiated harmonics from dV/dt 5-15 kV/μs MOSFET switching edges, common-mode current on phase wires acting as loop antenna, SMPS charger fly-back 50-200 kHz switching, Würth 742 711 21S / Fair-Rite Mix 31/43/44/77 ferrite-bead selection per frequency band, RC snubber 10 Ω + 1 nF per half-bridge, common-mode choke 3×2 mH soft-ferrite ring + 3×33 nF Y-cap, X2 (0.1-1 μF mains-to-mains) + Y1/Y2 (1-10 nF rail-to-chassis) safety-capacitor topology, ground-plane PCB return-path control, λ/20 aperture rule for shielded enclosure (≥20 dB attenuation), conductive EMI gasket (Chomerics ARclad / Würth WE-LT), AM-radio sniff DIY test 540-1620 kHz @ 9 m, smartphone BLE/Wi-Fi throughput diagnostic, RED 2014/53/EU mandatory presumption-of-conformity for Bluetooth/Wi-Fi radio modules, EMC Directive 2014/30/EU mandatory presumption-of-conformity for PLEV without radio
Engineering deep-dive into electromagnetic compatibility (EMC) and radio-frequency interference (EMI) on an e-scooter as the third cross-cutting infrastructure axis — parallel to [bolted-joint engineering as joining axis](@/guide/fastener-and-bolted-joint-engineering.md) and [thermal management as heat-dissipation axis](@/guide/thermal-management-engineering.md). Covers: 8-row standards matrix (EN 17128:2020 PLEV umbrella, CISPR 14-1:2020 emission, CISPR 14-2:2020 immunity, IEC 61000-3-2:2018 harmonics, IEC 61000-3-3:2013 flicker, IEC 61000-4-2:2008 ESD, IEC 61000-4-5:2014 surge, ETSI EN 301 489-17 V3.3.1:2024 BLE/Wi-Fi); 5-row interference-source matrix (motor controller PWM / SMPS charger / BLE radio / digital display+throttle / power-cable CM antenna); 6-row mitigation matrix (common-mode choke / RC snubber / clip-on ferrite bead / X+Y safety capacitor / PCB ground-plane + return-path / shielded enclosure + EMI gasket); 6-row test-method matrix (ESD ±8 kV contact / EFT ±2 kV / surge ±2 kV CM / radiated immunity 3-10 V/m / conducted immunity 3 V / harmonic ≤16 A); 6-row failure-diagnostic matrix (BLE drop / throttle creep / charger ground-fault / headlight flicker / AM-radio buzz / brake-light glitch); 8-step DIY EMI check (AM-radio sniff 540-1620 kHz @ 9 m, BLE/Wi-Fi throughput, ESD walk-test, visual ferrite/ground-strap inspection, chassis-to-DC- voltage measurement, surge-protected vs unprotected outlet comparison); 6-step DIY remediation (clip-on Würth/Fair-Rite ferrite, ground-strap tightening, shield-braid repair, antenna re-routing, IEC-marked charger replacement); RED 2014/53/EU + EMC Directive 2014/30/EU CE-marking presumption-of-conformity context; 15 numbered sections.